View CLAA156WA01A_4836999.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

c c h h u u n n g g h h w w a a p p i i c c t t u u r r e e t t u u b b e e s s , , l l t t d d . . t t e e c c h h n n i i c c a a l l s s p p e e c c i i f f i i c c a a t t i i o o n n to : date : accepted by : approved by checked by prepared by prepared by : tft-lcd product planning management division chunghwa pictuer tubes, ltd. 1127 hopin rd., padeh, taoyuan, taiwan 334, r.o.c. tel: +886-3-3675151 fax: +886-3-377-3001 doc.no: CLAA156WA01A issue date: tft lcd CLAA156WA01A www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 2 / 27 CLAA156WA01A record of revisions revision no. date description v1 2008/07/18 first issued v2 2008/08/18 pg 4 : revise operation temperature (max) v3 2008/09/05 pg 17 : color temperature coordinate : add the value of min and max. www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 3 / 27 CLAA156WA01A contents no. item page 1 overview 4 2 absolute maximum ratings 5 3 electrical characteristics 6 4 connector interface pin & function 10 5 interface timing chart 12 6 block diagram 14 7 mechanical specification 15 8 optical characteristics 17 9 reliability test conditions 21 10 handling precautions for tft-lcd module 23 11 appendix - isp enhanced extended display identification data (eedid) requirements 26 www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 4 / 27 CLAA156WA01A 1. overview CLAA156WA01A is 15.6? color (16 9) tft-lcd (thin film transistor liqu id crystal display) module composed o f lcd panel, lvds driver ics, control circuit and backlight. by applying 6 bit digital data, 1366rgb (3) 768, 262k-color images are displayed on the 15.6? diagonal screen. general specifications are summarized in the following table display area (mm) 344.232 (h)x193.536 (v) (15.6-inch diagonal) number of pixels 1366 3(h)768 (v) pixel pitch (mm) 0.252 (h)0.252(v) color pixel arrangement rgb vertical stripe display mode normally white number of colors 262,144(6bits)(lvds) gamut 60%(typ) optimum viewing angle 6 o?clock response time (ms) 8ms (typ) surface treatment glare viewing angle 40 40 /15 30(min.) brightness (cd/m^2) 220 cd/m 2 (5point)/6 ma (typ.) 200 cd/m 2 (5point)/6 ma (min.) uniformity 5point 80% 13point (65%) consumption of power (w) 6.35w max module size (mm) 359.8(w)210(h)6.2(d) max module weight (g) 520 (max) the lcd products listed on this document are not suitable for use of aerospace equipment, submarine cable, and nuclear reactor control system and life support systems. if customers intend to use these lcd products for applications listed above or those not included in the "standard" list as follows, please contact our sales in advance. standard computer, office equipment, communication equipment, test and measurement equipment, machine tool, industrial robot, audio and visual e quipment, other consumer products. www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 5 / 27 CLAA156WA01A 2. absolute maximum ratings the following are maximum value, which if exceeded, may cause faulty operation or damage to the unit. item symbol min. max. unit remark power supply voltage for lcd vcc 0 4.0 v lamp voltage vl 700 920 vrms lamp current il 2 6.5 marms *1). 2) lamp frequency fl 40 80 khz operation temperature top 0 50 *3). 4). 5). 6) storage temperature tstg -25 65 *3). 4). 5) delayed discharge time td -- 1 sec *7) note *1) product life-time relate to lamp current, please operate production follow statement at page 9 (b)back light . *2) when lamp current over the definition of absolute max, product life-time will decay rapidly or operate unusual. *3) the relative temperature and humidity range are as below sketch, 90%rh max. (ta 40 ) Q *4) the maximum wet bulb temperature 39 (ta Q 40 ) and without dewing. *5) if product in environment which over the definition of the relative temperature and humidity out of range too long, it will affect visual of lcd. *6) if you operate lcd in normal temperature range, the center surface of panel should be under 60 . *7) delay discharge time test condition starting lamp voltage=1650vrms . (please follow statement at page 9 (b) back light before test td, lamp should operate at least 1min, and lamp current should follow typical lamp current specification. to place panel at room temp. ( 252 )below for 24hrs,nd then to measure td with the same starting lamp voltage in dark room. www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 6 / 27 CLAA156WA01A 3. electrical characteristics (a) tft lcd tem symbol min typ max unit remark lcd power voltage vcc 3.0 3.3 3.6 v note 1 lcd power current icc - 400 500 ma note 2 rush crrent irush - - 2 a note 4 input voltage vin 0 - vcc v note 3 common voltage vcm 1.125 1.25 1.375 v note 3 diffrential input voltage vid 250 350 450 mv note 3 threshold voltage (high) vth - - 100 mv logic input voltage (lvds: in+,in-) threshold voltage (low) vtl -100 - - mv note 3 when vcm = +1.2v diffrential input voltage tolerance vid - - 35 mv common voltage tolerance vcm - - 35 mv note 1 power sequence 0.5 ms Q t1 10ms Q 1 sec t Q 4 0.01 ms t2 50 ms 200 ms QQ t5 0.01 ms t3 50 ms 200 ms QQ t6 www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 7 / 27 CLAA156WA01A vcc-dip state (1)when 3.0 vcc 2.7v R td 10 ms Q (2)when vcc 2.7v vcc-dip condition should as the vcc-turn-off condition. td 2.7v 3.0v vin=3.3v note 2 typical value is 0 63 gray level.(horizontal line pattern) 768 line mode vcc= +3.3v circuit condition (typ.) vcc=3.3 v f v =60 hz f h =48.36 khz f clk =75.44 mhz circuit condition (max.) vcc=3.3 v f v =60 hz f h =48.36 khz f clk =75.44 mhz note 3 lvds signal definite 64-gray www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 8 / 27 CLAA156WA01A vid = vin+ ? vin-, vcm = vcm+?vcm- , vid = vid+?vid- , vid+ = vih+?vih- , vid- = vil+?vil- , vcm =(vin+ +vin-)/2, vcm+ =(vih+ +vih-)/2, vcm- =(vil+ +vil-)/2, refer to inverter rated voltage [note 4] irush measure condition vin+ positive differential data clk input vin- negative differential data clk input www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 9 / 27 CLAA156WA01A (b) back light (a.) electrical characteristics ta=25 item symbol min typ max unit remark lamp voltage (il=6.0ma) vl 657 730 803 vrms il=6.0ma lamp current il 5.5 6.0 6.5 marms *1) inverter frequency fi 40 -- 60 khz *2) 1460 ta=25 lamp initial voltage vs 1600 -- vrms ta=0 (b) lamp life ? time item il at 2.0 ma il at 6.0 ma il at 6.5 ma unit remark lamp life-time (lt) min. 15,000 min. 15,000 min.15,000 hr continuous operation*3) turn-on and turn-off operation -- min.100,000 -- times continuous operation *4) *1)measure method galvanometer connect to low voltage *2) frequency in this range can make the characteristics of electric and optics maintain in +/- 10% except hue. lamp frequency of inverter may produce interference with horizontal synchronous frequency,and this may cause horizontal beat on the display. therefore, please adjust la mp frequency, and keep inverter as far from module as possible or use electronic shielding between inverter and module to avoid the interference.under optimum operate frequency range (50~80 khz), will not effect panel life-time and relability . *3) the voltage above vs should be applied to the lamps for more than 1 second for start-up. (inverter open voltage must be more than lamp starting voltage.) *4) definition of the lamp life time a. luminance (l) under 50% of specification starting lamp voltage b. starting lamp voltage: over130% of the initial value. ta=25 *5) for keeping good lighting situation, when design the inverter, it must be considered that the voltage large than starting lamp voltage. *6) wl=il x vl (il=6ma ta=25 ) lcd module + a inverter power supply www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 10 / 27 CLAA156WA01A 4. connector interface pin & function (a) cn1 (interface signal) outlet connector: fi-xb30sl-hf10 (jae) gs23302-0011s-7f(foxconn) link connector: fi-x30h (jae, link type) (note) ddc: display data requirements (note)refer to page6 78 9? data mapping pin no. symbol function 1 vss ground 2 vin +3.3v power 3 vin +3.3v power 4 v_edid ddc 3.3v power 5 nc no connect 6 clk_edid ddc clock 7 data_edid ddc data 8 r0n minus signal of channel 0(lvds) 9 r0p plus signal of channel 0(lvds) 10 vss ground 11 r1n minus signal of channel 1(lvds) 12 r1p plus signal of channel 1(lvds) 13 vss ground 14 r2n minus signal of channel 2(lvds) 15 r2p plus signal of channel 2(lvds) 16 vss ground 17 rclkn minus signal of clock channel (lvds) 18 rclkp plus signal of clock channel (lvds) 19 vss ground 20 nc no connect 21 nc no connect 22 vss ground 23 nc no connect 24 nc no connect 25 vss ground 26 nc no connect 27 nc no connect 28 vss ground 29 nc no connect 30 nc no connect (b) cn2 (backlight) backlight-side connector: bhsr-02vs-1 (jst) www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 11 / 27 CLAA156WA01A 5. interface timing chart (1) lcd input signal timing chart (a)horizontal timing sequence (b) vertical timing sequence: dclk first data 2 3 data (r,g, b) 1 1365 1366 invalid data invalid data last data t ha t hb dena t h t clk t vb dena t va invalid data line data 1 2 767 768 3 invalid data t v www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 12 / 27 CLAA156WA01A (2) timing chart item synbol min typ max unit frequency f clk 65.83 75.44 88.74 mhz dclk period t clk 15.19 13.25 11.11 ns horizontal total time t h 1414 1560 1700 t clk horizontal active time t ha 1366 1366 1366 t clk horizontal horizontal blank time t hb 48 194 334 t clk vertical total time t v 776 806 870 t h vertical active time t va 768 768 768 t h lcd timing dena ver ti c al vertical blank time t vb 8 38 114 t h note *1) data is latched during dclk falling period. *2) hd vd is negative. *3) dena (data enable) usually is positive. *4) during the whole blank period, dclk should keep input. during the vertical blank period, hd should keep input. www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 13 / 27 CLAA156WA01A (3) data mapping r data g data b data r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 color input data ms b ls b ms b ls b ms b ls b black 0 0 0 000000000 0 0 0 000 red(63) 1 1 1 111000000 0 0 0 000 green(63)0 0 0 000111111 0 0 0 000 blue(63) 0 0 0 000000000 1 1 1 111 cyan 0 0 0 000111111 1 1 1 111 magenta 1 1 1 111000000 1 1 1 111 yellow 1 1 1 111111111 0 0 0 000 basic color white 1 1 1 111111111 1 1 1 111 red(0) 0 0 0 000000000 0 0 0 000 red(1) 0 0 0 001000000 0 0 0 000 red(2) 0 0 0 010000000 0 0 0 000 red(62) 1 1 1 110000000 0 0 0 000 red red(63) 1 1 1 111000000 0 0 0 000 green(0) 0 0 0 000000000 0 0 0 000 green(1) 0 0 0 000000001 0 0 0 000 green(2) 0 0 0 000000010 0 0 0 000 green(62)0 0 0 000111110 0 0 0 000 green green(63)0 0 0 000111111 0 0 0 000 blue(0) 0 0 0 000000000 0 0 0 000 blue(1) 0 0 0 000000000 0 0 0 001 blue(2) 0 0 0 000000000 0 0 0 010 blue(62) 0 0 0 000000000 1 1 1 110 blue blue(63) 0 0 0 000000000 1 1 1 111 note 1) gray level: color(n) n is level order; higher n means brighter level. 2) data: 1: high 0: low www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 14 / 27 CLAA156WA01A 6. block diagram i/f connector cn1 (lvds receiver embedded) asic gate drivers power supply circuit tft-lcd g1 g2 g768 source drivers power timing signal display data s4097 s4098 s1 s2 1 2 cn2 dc-ac inverter light control inverter circuit (out side) 1 2 ccfl back light cn2 www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 15 / 27 CLAA156WA01A 7. mechanical specification (1) front side the tolerance, not show in the figure, is 0.5mm. [unit www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 16 / 27 CLAA156WA01A 2) rear side the tolerance, not show in the figure, is 0.5mm. [unit www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 17 / 27 CLAA156WA01A 8. optical characteristics ta=25 contrast ratio cr = 0 500 600 -- *1) 2) luminance (5p) l = 0 200 220 cd/m 2 *1) 3) uniformity(5p) ? l = 0 80 % *1) 3) uniformity(13p) ? l = 0 65 % *1) 3) tr = 0 3 6 ms *5) response time tf = 0 5 10 ms *5) cross talk ct = 0 3 1 % *6) horizontal 40/-40 45/-45 *4) view angle ver ti c al cr 10 R 15/-30 20/-35 *4) 0.283 0.313 0.343 w x y 0.299 0.329 0.359 0.599 0.629 0.659 r x y 0.303 0.333 0.363 0.262 0.292 0.322 g x y 0.550 0.580 0.610 0.130 0.160 0.190 color temperature coordinate b x y = 0 0.066 0.096 0.126 *3) gamut = 0 56% 60% *7) gamma gl 2.0 2.2 2.4 color coordinate and color gamut are measured by cs-1000, response time are measured by trd-100,and all the other items are measured by bm-5a (topcon). all these items are measured under the dark room condition (no ambient light). measurement condition: il=6.0ma inverter sumida / iv11145/t definition of these measurement items is as follows: *1) setup of measurement equipment the lcd module should be turn-on to a stable luminan ce level to be reached. the measurement should be executed after lighting backlight for 20 minutes and in a dark room. www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 18 / 27 CLAA156WA01A *2) definition of contrast ratio cr=on (white) luminance/off (black) luminance *3) definition of luminance and luminance uniformity central luminance: the white luminance is measured at the center position ?55? on the screen, see fig.1 below. 5p luminance (avg): the white luminance is measured at measuring points 33 37 55 73 77, see fig.1 below. 5p uniformity: ? l = (lmin / lmax) 100% (1,1) (1366,768) 342 683 1025 384 192 576 (1/10) w w h ( 1/10 ) h 1 8 7 6 5 4 3 2 9 10 11 12 13 fig.1 measure point www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 19 / 27 CLAA156WA01A *4) definition of view angle( *6) crosstalk modulation ratio : ct= O y b -y a O / y a 100% y a y b measure position and definition y a means luminance at gray level 32(exclude gray level 0 pattern) y b means luminance at gray level 32(include gray level 0 pattern) luminanc white black 90 % 90 % 10 % 10 % tf tr upper(+) right(+) left(-) gate drive side lcd panel lower(-) www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 20 / 27 CLAA156WA01A *7) definition gamma (vesa) based on customer sample, take the average value as a standard center value and the variation range of gamma value caused by loop voltage error should be between +/- 0.2. the bellow figure shows how to obtain the gamma curve and (from gray level: 0 4 8-----60 63). y =x-k log( y) log gray level www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 21 / 27 CLAA156WA01A 9.reliability test conditions 9.1 temperature and humidity test items conditions high temperature operation 50 ? 240hrs high temperature storage 60 ? 240hrs high temperature high humidity operation 50 ?90 rh 240hrs high temperature high humidity storage 60 ?90 rh 48 hrs low temperature operation 0 ? 240 hrs low temperature storage -20 ?240 hrs thermal shock -20 (0.5 hr) 60 (0.5 hr) ramp<20 100 cycle 9.2 shock & vibration test items conditions shock (non-operation) shock level : 1960m/s 2 (200g), waveform : half sinusoidal wave, 2ms, 6 axis ( x, y, z) per cycle vibration (non-operation) vibration level : 9.8m/s 2 (1.0g), sinusoidal wave (each x, y, z axis : 1hr, total 3hrs) frequency range : 5 500 hz sweep speed : 0.5 octave/min. 9.3 esd surface discharge(panel display area frame pwb panel back side) electrics capacity of connector contact air contact capacity 150 pf 150 pf 200 pf resistance 330 ? 330 ? 0 ? voltage 8kv 8kv/15kv 250 v interval 1 sec 1 sec 1 sec times(single point) 25 25 1 air discharge air discharge acceptance criteria +/-8 kv +/-15 kv a permitted permitted b permitted permitted c not permitted permitted d not permitted not permitted acceptance definitions a normal operation. no degradation. no failures. b some performance degradation allowed. no data lost. self-recoverable. c temporary performance degradation. recovery by operator is acceptable. d degradation or loss of function,which is not recoverable due to damage of equipment (components) www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 22 / 27 CLAA156WA01A 9.4 mtbf without b/l: 200,000 hrs (min) lifetimes. 9.5 judgment standard the judgment of the above test should be made as follow: pass normal display image with no obvious non-uniformity and no line defect. partial transformation of the module parts should be ignored. fail no display image, obvious non-uniformity, or line defects. www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 23 / 27 CLAA156WA01A 10. handling precautions for tft-lcd module please pay attention to the followings in handling- tft-lcd products; 10.1 assembly precaution (1) please use the mounting hole on the module side in installing and do not beading or wrenching lcd in assembling. and please do not drop, bend or twist lcd module in handling. (2) please design display housing in acco rdance with the following guidelines. ? housing case must be destined carefully so as no t to put stresses on lcd all sides and not to wrench module. the stresses may cause non-uniformity even if there is no non-uniformity statically. ? keep sufficient clearance between lcd module back surface and housing when the lcd module is mounted. approximately 1.0 mm of the clearance in th e design is recommende d taking into account the tolerance of lcd module thickness and mounting structure height on the housing. ? when some parts, such as, fpc cable and ferrite plate, are installed underneath the lcd module, still sufficient clearance is required, such as 0.5mm. th is clearance is, especially, to be reconsidered when the additional parts are imple mented for emi countermeasure. ? design the inverter location and conn ector position carefully so as not to give stress to lamp cable, or not to interface the lcd module by the lamp cable. ? keep sufficient clearance between lcd module and the others parts, such as inverter and speaker so as not to interface the lcd module. approxima tely 1.0mm of the clearance in the design is recommended. (3) please do not push or scratch lcd panel surface with any-thing hard. and do not soil lcd panel surface by touching with bare hands. ( polarizer fi lm, surface of lcd panel is easy to be flawed.) (4) please do not press any parts on the rear side such as source tcp, gate tcp, control circuit board and fpcs during handling lcd module. if pressing rear part is unavoidable, handle the lcd module with care not to damage them. (5) please wipe out lcd panel surface with absorbent cotton or soft clothe in case of it being soiled. (6) please wipe out drops of adhesives like saliva and water on lcd panel surface immediately. they might damage to cause panel surface variation and color change. (7) please do not take a lcd module to pieces and rec onstruct it. resolving and reconstructing modules may cause them not to work well. (8) please do not touch metal frames w ith bare hands and soiled gloves. a color change of the metal frames can happen during a long preservation of soiled lcd modules. (9) please pay attention to handling lead wire of backlight so that it is not tugged in connecting with inverter. 10.2 operating precautions (1) please be sure to turn off the power supply befo re connecting and disconn ecting signal input cable. (2) please do not change variable resi stance settings in lcd module. they are adjusted to the most suitable value. if they are changed, it might happen lcd does not satisfy the characteristics specification. (3) please consider that lcd backlight takes longer time to become stable of radia tion characteristics in low temperature than in room temperature. www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 24 / 27 CLAA156WA01A (4) a condensation might happen on the surface and insi de of lcd module in case of sudden change of ambient temperature. (5) please pay attention to displaying the same pattern for very long time. image might stick on lcd. if then , time going on can make lcd work well. (6) please obey the same caution descrip tions as ones that need to pay a ttention to ordinary electronic parts. 10.3 precautions with electrostatics (1) this lcd module use cmos-ic on circuit board and tft-lcd panel, and so it is easy to be affected by electrostatics. please be careful w ith electrostatics by the way of y our body connecting to the ground and so on. (2) please remove protection film very slowly on the surface of lcd module to prevent from electrostatics occurrence. 10.4 storage precautions (1) when you store lcds for a long time, it is recommended to keep the temperature between 0 ~40 without the exposure of sunlight and to keep the humidity less than 90%rh. (2) please do not leave the lcds in the environment of high humidity and high temperature such as 60 and 90%rh. (3) please do not leave the lcds in the e nvironment of low temperature(below -20 .) 10.5 safety precautions (1) when you waste lcds, it is recommended to crush damaged or unnecessary lcds into pieces and wash them off with solvents such as acetone and ethanol, which shoul d later be burned. (2) if any liquid leaks out of a damaged-glass cell and comes in contact with the hands, wash off thoroughly with soap and water. 10.6 others (1) a strong incident light into lcd panel might cause display characteristic changing inferior because o f polarizer film, color filter, a nd other materials becoming inferi or. please do not expose lcd module direct sunlight land strong uv rays. (2) please pay attention to a panel side of lcd module not to contact with other materials in preserving it alone. (3) for the packaging box, please pay attention to the followings: ? packaging box and inner case for lcd are designe d to protect the lcds from the damage or scratching during transportation. please do not open except picking lcds up from the box. ? please do not pile them up more than 3 boxes. (the y are not designed so.) and please do not turn over. ? please handle packaging box with care not to give th em sudden shock and vibra tions. and also please do not throw them up. www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 25 / 27 CLAA156WA01A ? packing box and inner case for lcds are made of cardboard. so please pay attention not to get them wet. (such like keeping them in high humid ity or wet place can occur getting them wet.) www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 26 / 27 CLAA156WA01A www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/
cpt chunghwa pictures tubes, ltd., cpt confidential 27 / 27 CLAA156WA01A www.yslcd.com.tw studio technology co.,ltd www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of CLAA156WA01A

	To Download CLAA156WA01A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .